Written by Dale Richardson - Updated: June 23, 2023
Stay Updated with Expert Tips!
Love our DIY guides and solutions for common household problems? Get expert advice, tips, and exclusive offers in our newsletter. From garden hacks to home maintenance and special deals, we've got it all. Join our growing community now!
Your toes might feel toasty but a warm floor is a reason for concern. Learn why your kitchen floor has a hot spot and how to fix it.
The top cause for a warm kitchen floor is a slab leak. Slab leaks can appear in different forms but all of them are caused by plumbing that leak. When the kitchen floor feels hot then the leaking pipe is probably connected to the hot water heater.
Leaking water can cause a lot of damage to the home. Learn more about how slab leaks happen and what you can do about them.
Read Next: This is why your kitchen floor is raised .
A slab leak describes the situation well. Somewhere in your home, a pipe or pipes are leaking. The water then creeps under the concrete slabs of a floor, spreading until it becomes noticeable. This can happen when you feel a hot spot in tiled or vinyl flooring areas or you see a water stain spreading over a bare concrete floor.
There are always exceptions but the most common type of plumbing that cause slab leaks are the copper pipes that run below the foundation of a home. These water pipes ferry both cold and hot water to faucets and other outlets.
It is not uncommon for copper pipes to spring a leak. Here are just some of the conditions and reasons why your plumbing might be dripping.
When you feel a hot spot in your home, whether it is in the kitchen or bathroom, then the water damage is likely being caused by a pipe that is connected to a hot water heater. The warm water spreads under the flooring and heats up the concrete.
READ NEXT: Copper pipes in concrete - yes or no?
Yes, slab leaks can be fixed. However, it often requires breaking the floor and other heavy-duty stuff. Correcting a leaking copper pipe and damaged concrete is something best left to a professional company. The nature of slab leaks is challenging, even to experienced DIY handymen.
Any heavy-duty repair job requires safety clothing. Here are the best safety boots available on the market today.
Once the leak has been located, the flooring and concrete will be broken with a jack-hammer to reach the pipes. Considering the level of demolition involved, it is important to make sure that the person you hire is an expert. They will be able to break through the concrete with minimal damage.
Once the concrete is out of the way, the repair team will dig through the dirt to locate and fix (or replace) the copper pipe.
We also have the best hammer drill reviews in case you want to beef up your toolbox.
This is a great way to avoid damageing the inside of your home. While an additional bonus is the chance to replace larger sections of plumbing, this method has one major drawback. This is precision work that needs an entire excavation team and perfect planning.
Sometimes, it is best just to take a leaking location out of the equation. That is what re-routing does. The repairs are not focused on fixing the pipe that is leaking under your home (although it is put out of commission so it will no longer work or drip). Re-routing takes the copper pipeline above ground, sometimes through the attic and walls.
Any job that requires ceiling work or installing something high on a wall can be dangerous. Make sure that you use the right ladder for the job.
This method also decommissions the leaking pipeline but instead of going above ground like the re-routing technique, pass-through inserts a smaller line inside the leaking line. The water then runs through this smaller line, eliminating the broken pipe altogether.
READ NEXT: 3 Ways to fix a bouncy kitchen floor.
It can be hard to protect your home from a slab leak. After all, logic demands that you get rid of the copper pipes and that can be expensive. Why get rid of the copper pipes? Because they are more vulnerable to the corrosion, municipal-added chemicals in the water, and water pressures. If you do not want to go through the hoopla of replacing the pipes, you might want to ensure that the water pressure in your home is not too high.
Testing your home’s water pressure is easy and inexpensive. You only need to buy a hand-held pressure water gauge if you do not already have one.
Step 1: You are going to use your outdoors hose bib or faucet. The one you use to attach the garden hose.
Step 2: Make sure that no water is being used inside the house for the duration of the test. This could result in a false reading.
Step 3: If there is a hose attached to the faucet, it must be removed. For an accurate reading, you must test the faucet and not the hose. (Here are the best garden hose reviews ).
Step 4: Open the faucet fully and check the reading. A normal reading is anything between 40 to 60 psi.
Step 5: If the pressure is too high, you need to adjust the pressure regulator or have it replaced.
There are several options that you can consider. The trick is to choose something that is corrosion-resistant and comes with a long lifespan. Two materials that fit the bill are plumbing-grade plastic and stainless steel.
One More Thing Before You Go!
Craving more DIY insights? Don't miss our expert guides and exclusive deals. Subscribe now and get the best of home and garden tips straight to your inbox. Join our community and stay in the know!
Get Cashback Faster & Earn Free Fraffle Tickets
Shop at your favourite stores and enjoy cashback in days, not months. Plus, sign up today to get 5x Free Fraffle tickets!